Download Commodity

Download Article

Spurs tin assistance improve communication between a passenger and a mount. If you've selected a shiny new pair of spurs, yous may be wondering how to adhere them to your favorite cowboy boots. The process is quite simple and should only take a few minutes. Once you lot understand and gather your new spurs, you'll have them on your boots and be riding in no time.

  1. i

    Locate the spur ledge on the back of your cowboy kicking. The spur ledge is the protruding part of the boot heel that creates a small shelf where the spur heel band volition residuum.[one]

    • The spur ledge is a very slight ledge, just large enough so that the heel band doesn't slip downwards the kicking.
    • All cowboy way boots should have a spur ledge. If you are not sure most your boots, have them with y'all when you go to buy your spurs.

  2. two

    Find the heel ring portion of the spur. The heel band is the U-shaped piece of metal that wraps around the kick's heel and is held on by a strap. The heel band may have buttons where the straps will adhere or bars for threading straps to adhere.[2]

    • You will need a heel band that is approximately the same size equally the heel portion of your cowboy boot.

    Advertisement

  3. 3

    Choose 1 long strap if the heel band has bars. If the heel ring has bars on both sides, you volition demand 1 long strap with a buckle on i end to adhere the heel band to the boot.[3]

    • Take a await at your strap to see if information technology has a decoration, metal piece of work, or fancy pattern on one side. Y'all want the decorative side to e'er be visible on the exterior of your boot.

  4. 4

    Go ii small straps if the heel ring has buttons. If the heel band has buttons on both sides, you will need ii smaller straps with buttonholes. These will ultimately buckle together after being attached to both sides of the heel band.[4]

    • Accept a look at your straps to see if either of them have a decorative, scalloped, or fancy side. You lot want the decorative side to e'er be visible on the outside of your boot.

  5. 5

    Wait for the shank on the spur. The shank is a pocket-sized metal piece that extends from the center of the heel ring. The shank should point down once the spur is in place on the boot.[5]

  6. half dozen

    Spot the rowel on the dorsum of the spur. The rowel is the rotating deejay with blunt points attached to the shank on the heel band. This is the most important part of the spur because information technology is the office you will utilize to nudge your horse in the side to communicate your intentions with him.[6]

    • Exercise caution when handling the rowel so that you don't accidentally cut yourself. About aren't incredibly sharp but could however cause pain if grabbed too tightly.

    7. Advertisement

  1. one

    Assemble all the pieces needed to get together your spur. You'll need to grab your boots, heel band (with rowel attached), and the straps you lot volition be using. This is a perfect time to position any decorative strap sides where y'all desire them before attaching them to the heel band.

  2. 2

    Attach button straps onto heel bands with buttons. For this type of heel ring, you will need 2 small-scale straps with buttonholes.[7] The straps will be fastened on either side of the heel band and then buckled beyond the kick after.

    • Hold the heel ring in your paw with the shank facing down.
    • Start with i side of the heel band and identify the first strap with the buttonhole over the heel band button.
    • Spread the buttonhole apart to push the button through the pigsty.
    • Rotate the strap around the button until it lays down flat.
    • Repeat with the other side of the heel band and adhere the second strap.

  3. 3

    Thread straps into a heel band with bars. For this type of heel band, you will need 1 longer strap with a buckle.[8] With one long strap you will thread it through both sides of the heel band and buckle information technology across the boot later.

    • Hold the heel band in your hand with the shank facing down.
    • Begin threading the strap from the inside of the outward facing heel band bar.
    • Thread the strap through the bars. The buckle should end up on the outside of your boot.
    • Exit some strap to go nether the boot and so thread the same strap into the other side of the heel band through the bars.

    4. Advertisement

  1. 1

    Fit the heel band to the spur ledge of your boot. The heel band should residual on the spur ledge with the shank facing down. The fit should not be likewise tight or too loose. There should be a picayune bit of movement for the spur to fit correctly. If the fit is off just slightly, you lot may be able to gently pull information technology apart to loosen it or squeeze a bit to tighten it.[9]

  2. 2

    Attach the spur to your boot past buckling the straps. Once the heel band is fitted in place at the dorsum of your boot, buckle the strap or straps together over the kick to create a snug fit.[10]

    • Put the buckles on the outside of the boots. If the buckles are facing the inside of the boots, they will rub together at your ankles and be uncomfortable.

  3. 3

    Adjust the strap so that the spur fits snugly onto the boot. If the spur is as well tight or likewise loose once buckled onto your boot, yous may need to allow some strap in or out of the buckle to suit the fit.[eleven]

    • Offset by unbuckling the strap. Next, adjust the length of the strap as needed to ensure a expert fit. Stop upward by re-buckling the strap.

    4. Advertizement

Add New Question

  • Question

    Could I wear my spurs to school? (I'k in middle school)

    Community Answer

    That's a great idea! Equally long equally information technology follows your schoolhouse'due south dress code and you're fine with the possibility of a few stares (or high-fives!)

  • Question

    My spurs have a double heel chines. Exercise they go in front of the heel or ane on each of the heel?

    Community Answer

    The spurs on your boots take one on each heel. With two, the shoes would be too heavy to walk in and y'all would seriously hurt your cattle whilst riding.

  • Question

    What practice I do if my shoes do non take ledges? Tin I get a type of spur that doesn't need them?

    Community Answer

    Yes, you tin. they are called portable spurs. Withal, they may not have any portable spurs locally, y'all might demand to purchase them online.

Ask a Question

200 characters left

Include your e-mail accost to get a message when this question is answered.

Submit

Advertisement

  • If you are having trouble attaching the spur to your boot while you are wearing the boots, try plumbing equipment the spur to the boot and buckling them in place before slipping the boot onto your pes.

Thanks for submitting a tip for review!

Advertisement

References

About This Article

Cheers to all authors for creating a page that has been read 61,889 times.

Did this article assist you lot?